BlueSYSTEM BASIC

The BlueSYSTEM BASIC forms part of the BlueSYSTEM family, the latest generation of electronic inclination measuring instruments and systems. BlueSYSTEM BASIC normally consists of one or two BlueLEVEL BASIC measuring instruments and a display unit BlueMETER BASIC. Depending on the application the BlueMETER BASIC can also be connected to a PC with evaluation software allowing the on-line evaluation and presentation of the measured values.

 

This latest generation of high precision electronic inclination measuring instruments is specifically suitable for the precision measurement of smallest angles. Applications are therefore in particular the measurement of flatness of surface plates or the measurement of the geometry of machine tools. The sensor itself, the heart of every precision measuring instrument, has been further developed, to allow precise measurements even under critical environmental conditions.


The key features of this new series of instruments are:

  • Compact and pleasant design which is functionally optimized for precision measurement
  • Since each instrument has a built in Infrared receiver, the measurement can be initiated at any instrument
  • Display of measuring values through BlueMETER BASIC
  • The BlueLEVEL BASIC is available in 2 sensitivities:

     - 0.001mm/m: range ±10 mm/m

     - 0.005mm/m: range ±50mm/m

  • Linearity according to DIN 2276/2
  • All instruments are equipped with RS232 / RS485 interfaces
  • Powered by standard batteries 1.5V; size C
  • In compliance with CE regulations and all applicable EMC regulations

     

Calibration Certificate

The BlueLEVEL BASIC can be delivered with an internationally recognised Calibration Certificate against a surcharge.

STRAIGHTNESS

  • Measurement of granite straight edges
  • Measurement of machine tool guideways
  • Air plane configuration checking (under different loads)
  • General load depending geometrical elements

PARALLELISM

  • Measurement of machine tool guide ways
  • Measurement of geometry of machines
  • Adjustment of printing machine assembly
  • Adjustment of platforms

FLATNESS

  • Flatness of measuring and setting plates in laboratories and on the shop floor
  • Flatness of tables of machine tools
  • Flatness of connecting surfaces of assemblies and subassemblies

SQUARENESS

  • Measurement of  machine tool guideways 
  • Measurement of master squares
  • Measurement of angular deviation between spindle and other elements of a machine tool

MACHINE TOOLS / ROTATION CHECKS

Measuring task / Goal:
A machine tool must be checked on possible geometrical deviations. The check must show up eventual rotations of the table during displacement. The measurement of geometry should be made in a quick, reliable and simple procedure ant thus with a good cost-benefit effect.

more

MACHINE TOOLS / ROTATION CHECKS

Measuring task / Goal:
A machine tool must be checked on possible geometrical deviations. The check must show up eventual rotations of the table during displacement.

The measurement of geometry should be made in a quick, reliable and simple procedure ant thus with a good cost benefit effect.

more

MEASURING - CALIBRATION / FLATNESS MEASUREMENT, ANGLES

Measuring task / Goal:
The calibration of granite master squares should be performed as easily and efficiently as possible. The equipment used should offer a good cost-benefit relationship and requirements regarding the qualification of staff should be as moderate as possible, enabling workshop staff to easily make use of the system.

more

MEASUREMENT OF THE ABSOLUTE POSITION OF A GUIDEWAY

Measuring task / Goal:
For a guideway not only its straightness but also its deviation from the horizontal plane shall be measured. Furthermore it should be determined where and how much should be corrected to adjust the guideway horizontally.

more

LARGE GRINDING MACHINE WITH FLAT GUIDEWAYS

Measuring task / Goal:

On a surface grinding machine with 18-meter-long guideways set 1.3m apart, the co-parallelism of the two guideways has to be checked periodically. The guideways have to be within a plane with a maximum tolerance (error) of less than 0.1 mm. The complete machine and its guideways can be adjusted by means of supporting screws placed at 750 mm intervals.

more

FLATNESS MEASUREMENT ON A CIRCULAR SUPPORT OF A TURN TABLE

Measuring task / Goal:
The flatness of a circular support with 2.3m diameter has to be measured.

more

MEASUREMENT OF A CIRCLE ON A ROUND TABLE OF A GRINDING MACHINE

Measuring task / Goal:

The flatness of a rotating table of a grinding machine with a diameter of
3200 mm has to be measured. Thereby only the flatness of a circle has to be measured and not the whole table.

more

MEASUREMENT OF PITCH AND ROLL ON A GRINDING MACHINE

Measuring task / Goal:

On a large surface grinding machine with guide ways with a length of 18m and a distance of 1.3 m pitch and roll have to be checked regularly. The maximum tolerance is 0.1 mm/m.

more

MEASUREMENT OF THE RECTANGULARITY OF THE HEAD OF A ROUND TABLE GRINDING MACHINE

Measuring task / Goal:

The rectangularity of the axis of a grinding head of large grinding machine in relation to the support of a round table with a diameter of 3200 mm has to be measured. Based on the results the inclination of the head has to be adjusted.

more

DAM MONITORING

Measuring task / Goal:

The inclination and inclination change of a dam is monitored and put in relation to climatic conditions and fill level of the dam. The sensors are mounted permanently and have an excellent zero point stability. The measured values are evaluated in a central station about 10km ( 6 miles ) away. 

more